Have you discovered a prehistoric TV in your attic and don't know what to do with it? Well, this one, with imitation wood and convex large and round buttons? I'm sure it simply can't compete with modern flat screen TVs, but that's no reason to throw it straight into the trash heap - if you're a creative person. By the way, you can turn your old TV in a unique aquarium. Just follow these instructions.

So ladies, this post is for boys, so here is a link to branded wedding dresses for you. If your man can make an aquarium according to these instructions, then feel free to marry him. His hands know what to do;)

1. Find an old wooden console TV.2. Open the wooden console itself. Console TVs usually have a removable back cover, although you may have to remove the side cover as well.
3. Disconnect all electrical components.
Be especially careful not to damage the cathode ray tube, as older models can also be very dangerous. See warnings for additional information.

4. If necessary, remove any internal partition panels. If you don't plan to use them for design, remove the inner compartments to free up space inside.
5 . Consider whether or not you need to remove any control buttons. They may or may not protrude from the wooden console, depending on the TV model. Since your goal is to clean out the console to make room for the aquarium, you may have to remove a few buttons; however, if they are screwed to the same plate, leave them in place and install the necessary components on the side panels or corners of the case (for example, an air compressor).
6. Measure the inner chamber of the TV.
If necessary, measure the area for the future aquarium and its components separately.
7. Buy the necessary components for the aquarium. Using the TV's internal measurements, purchase the aquarium and all additional necessary components, including a filter, air compressor, light bulb, and tubing. Make sure the aquarium is wider and slightly higher than the screen itself. Be especially careful and remember to leave space between the top of the aquarium and the console lid for overhead light, which will be needed for the fish and plants if they are enclosed in a dark box.
Place an air compressor inside the console to reduce noise. However, it can be installed outside if there is not enough space there.

If you don't have the space to place an overhead light inside, use an LED ballast instead.
If your console TV won't fit a standard aquarium size, you'll have to have it custom made.
8. Place the aquarium inside the empty TV. Place it inside your console TV and make sure there is a place for everything. Don't install the aquarium yet.
9. Use a drill to make holes for the tube in back cover console if necessary. Also, if possible, make additional holes to improve ventilation and prevent condensation.
10. Make the top cover. The most the best way will cut out the entire existing top panel at the seams.
Attach hinges to the base and secure them to the lid so it can be closed and opened. Alternatively, you can throw out the existing top panel altogether and replace it with a flip top made from a new piece of wood, matched to the color of your old console TV.
Put it back back panel TV.
11. Strengthen the bottom of the console if necessary. If you're not sure the bottom can hold gallons of water, you can either replace it with a stronger piece of wood or reinforce it underneath with another piece of wood or a metal lid.
12. Seal all surfaces several times. Use a waterproof polyurethane sealant to protect confined spaces from water damage.
13. Install a voltage stabilizer on the outside of the rear wall of the case, if necessary.
If you need to run a cord from the water tank to the power source and it doesn't reach the wall, attach a voltage stabilizer with a long cord directly to the back of the aquarium to bridge the distance. 14. Assemble the aquarium inside the console.
Install all the above components before filling the aquarium with water and fish, check that everything is working properly. This is absolutely necessary if you want them to live for more than a week or two. If you place the fish directly into the aquarium, then the ammonia formed during the decomposition of their waste products will accumulate in the water faster than beneficial bacteria. So first you need to start the filter and then leave the aquarium alone for at least three days.
15. Done.
Adviсe

Connect the aquarium light through one of the controls on the original TV. To do this you just need to remove it.
Choose an aquarium that is larger than the width of the screen and you will have more water in it, plus you can hide the filter and heater.
This kind of insulation using a console TV for your aquarium will allow you to maintain a constant temperature in it.
Choose a beautiful background for your TV aquarium. You can use underwater scenes (which can be found at most pet stores), or you can choose your own background. (Take measurements and fit your image, then head to your local print shop and print.)
Use the extra space inside as storage for food and cleaning tools.

Warnings

You can take your old TV to a repair shop and have them remove the CRT (Cathode Ray Tube). While the contents of a CRT are usually not dangerous, the air inside the vacuum tube itself can explode if the tube has been cracked or otherwise damaged. (A TV tube until 1960 did not have built-in explosion protection and could be extremely dangerous. If it has a label on it that says something like this: “This tube has built-in explosion protection.”, then you can remove it yourself. If you didn’t see inscription, then it is better to take the TV to a workshop.)
If you are using an existing TV stand, make sure it is strong enough to handle the weight of the water.
Capacitors and other electronics can retain a charge for many years after they were last used. Danger of defeat electric shock may still exist, so care should be taken when removing and disposing of electronic components.
Radiation shielding and other components may have very sharp edges.
Make sure you are willing to take on the responsibility of purchasing and maintaining an aquarium. You'll have a lot more trouble than you think!
Make sure you have finished setting up the enclosure before you start placing the aquarium inside.

If you find an old Soviet-era TV in the pantry, which has wood decor, speakers and niches in the lower part of the structure, then you should not rush to throw it in the trash. From such a rare installation you can make a completely unique aquarium.

The TV is turning, the TV is turning... into an aquarium!

First you need to open the wooden console, which can be done by removing the back cover. Next, you need to disconnect the internal components, and you also need to get rid of the separating panels.

Then you need to measure the internal space of the structure, this will allow you to purchase elements for making an aquarium that correspond to certain dimensions. You will need tubes, a filter, a compressor and a light bulb. You should make an aquarium that will exceed the width and height of the screen.

It is necessary to provide free space between the edge of the aquarium and the lid of the structure, which will allow the installation of an overhead light. The compressor must be located inside the structure, which will prevent the spread of noise. The glass base should be placed inside the empty TV.

Final work

Using a drill, you need to make the necessary holes in the back cover. And the presence of additional holes will provide better ventilation, which will prevent the formation of condensation.

Next, you will need to make a top cover; the most successful option would be a top panel that can be cut at the seams. In order to use such a door conveniently, you should fix the hinges on the lid. The top panel may not be used; instead, you can use a flip cover made of wood. It will only be important to choose a blank that matches the color.

The previously removed rear panel can be reinstalled. The bottom of the structure must be further strengthened, as it will have to undergo significant loads. To do this, you can use a stronger workpiece. Strengthening may also involve fixing another piece of wood. A more reliable option would be to use a metal lid.

In order to prevent leaks, it is necessary to ensure reliable sealing of joints and surfaces in several approaches. A waterproof polyurethane composition will do the job perfectly.

We often feel sorry to part with our favorite things, even if they have long been broken or lost their relevance. In this case, designers offer many original solutions that give old things a new life. It's hard to believe, but an ordinary Soviet TV can turn into an exclusive and functional piece of furniture. You just need to make some effort, use your imagination, and then the result will exceed any expectations.

Currently, technology does not stand still and is constantly evolving. Bulky, black-and-white TVs have been replaced by various plasma panels and LCD devices capable of fantastically reproducing any image. Therefore, many people long ago got rid of Soviet-era equipment - they disassembled it for spare parts or took it to a landfill. If you still have a rare copy somewhere on your balcony or in your dacha, there is no need to rush to get rid of it. You can make a lot of unique things out of an old device using a minimum of available materials.

One of the most interesting and popular options is an aquarium.

To make an original vessel for fish, it is best to use a wooden console TV. First of all, you should remove the back cover and carefully remove all electrical parts. ATTENTION!

It is necessary to be extremely careful when disconnecting all the insides of the TV, especially the ray tube (usually it is located in the very center).

1. When only the foundation remains, experts advise adhering to the following algorithm of actions: You can give your future aquarium a more attractive appearance by covering wooden case
2. special varnish. It is worth waiting a while until the product is completely dry.
3. Using a tape measure, you need to carefully measure the empty body of the old device.
4. In a specialized store, you should purchase an aquarium that is suitable for specific sizes.
5. Designers recommend covering the back wall of the aquarium with a special film. It would be good if it had a marine-themed image on it.
6. Next, you need to remove the upper part of the case and make it completely removable. This is necessary to make it easy to feed the fish. You can also install hinges, then you get a folding design.
7. Since fish require warmth and light, it is advisable to screw a small lamp below.

After all the preparatory work, the aquarium is filled with water, inserted into the body of the old TV and the fish are released. An aquarium requires settled water with special beneficial additives. Ordinary tap water will lead to the rapid death of fish.

All that remains is to connect the lamp and enjoy the spectacular interior detail. But the imagination of designers is far from limited to this.

Minibar from TV receiver

Surely not everyone has a personal minibar at home. This problem can be easily solved using an old TV receiver. You just need to follow a certain plan:

1. All electrical parts must be carefully removed from the unnecessary device.
2. If there is a plastic cover installed at the back, it is better to remove it and screw a suitable-sized piece of fiberboard or plywood to the body.
3. For more attractive appearance, the inner walls of the future product should be covered with a beautiful film to suit your taste or mirrors installed. To attach mirrors to pieces of furniture, mounting tape, silicone or special compounds are usually used.
4. It is advisable to make a small backlight inside the case from LED strip(sold in specialized stores).

To make an original vessel for fish, it is best to use a wooden console TV. First of all, you should remove the back cover and carefully remove all electrical parts. Additionally, a front hinged cover can be manufactured and installed. She will hide alcoholic drinks from prying eyes.

Among other things, many home craftsmen pay special attention to the external decoration of the TV case. The result is unique products. Here everything should depend on individual preferences and capabilities.

Pet house made from an unwanted TV

A forgotten old TV can easily turn into a beautiful and cozy house for a cat. To do this you need to proceed as follows:

1. Carefully remove all the “internals” from the old device, leaving only the box. It will be the new home for your beloved pet.
2. Various accessories, bright stickers and special paints and varnishes will help you create an original design. Everything is limited only by the imagination of the master.

REFERENCE! Your domestic cat will probably be happy with the gift, since almost all cats have a special passion for boxes. This is explained by the animal’s instinctive desire to hide in a secluded place.

TV cabinet

Another original option is a stylish cabinet for books, jars of spices or some other small things. This product will not take up much space and will fit harmoniously into any interior. As in previous cases, to create of this subject

1. Carefully measure the empty body, make and install shelves and doors (some can do without them).
2. Decorate an original piece of furniture to your taste. So, you can paint the product in a bright color that harmonizes with the overall style of the interior, or cover it with film or wallpaper.

To complete the work, you should put the cabinet in place and fill it with various small items.

Flower bed

An old TV can become an exclusive decoration for a flower garden or vegetable garden. The easiest way to make an original flower bed is as follows:

1. To begin with, the rare model is freed from all the “stuffing”.
2. You need to pour a sufficient amount of soil inside the box, sow flower seeds and place it in a sunny place.

REFERENCE! If you immediately transplant a beautiful flower into a new flowerbed, you won’t have to wait for the seeds to germinate.

The new flower bed can be hung somewhere. In this form, the design will look very interesting.

Thus, there is no need to rush to get rid of old things. Using your imagination and available tools, you can easily breathe new life into them. All your efforts will quickly pay off. Instead of gathering dust on the balcony or in the closet, an ordinary black and white TV can turn into a unique piece of furniture. It will not only significantly transform the design of the room, but will also continue to benefit its owners.

How to make a fish aquarium from an old TV

Have you discovered a prehistoric TV in your attic and don't know what to do with it? Well, this one, with imitation wood and convex large and round buttons? I am sure that it is simply not able to compete with modern flat-screen TVs, much less home theaters, with stunning image and sound, also amplified by AV receivers.

But this is not a reason to send the old man straight to the trash heap - if you are a creative person. By the way, you can turn your old TV into a unique aquarium. Just follow these instructions.

1. Find an old console wooden TV.

2. Open the wooden console itself. Console TVs usually have a removable back cover, although you may have to remove the side cover as well.

3. Disconnect all electrical components.

Be especially careful not to damage the cathode ray tube, as older models can also be very dangerous. See warnings for more information.

4. If necessary, remove any internal partition panels. If you don't plan to use them for design, remove the inner compartments to free up space inside.

5 . Consider whether or not you need to remove any control buttons. They may or may not protrude from the wooden console, depending on the TV model. Since your goal is to clean out the console to make room for the aquarium, you may have to remove a few buttons; however, if they are screwed to the same plate, leave them in place and install the necessary components on the side panels or corners of the case (for example, an air compressor).

6. Measure the inner chamber of the TV.

If necessary, measure the area for the future aquarium and its components separately.

7. Buy the necessary components for the aquarium. Using the TV's internal measurements, purchase the aquarium and all additional necessary components, including a filter, air compressor, light bulb, and tubing. Make sure the aquarium is wider and slightly higher than the screen itself. Be especially careful and remember to leave space between the top of the aquarium and the console lid for overhead light, which will be needed for the fish and plants if they are enclosed in a dark box.

Place an air compressor inside the console to reduce noise. However, it can be installed outside if there is not enough space there.

If you don't have the space to place an overhead light inside, use an LED ballast instead.

If your console TV won't fit a standard aquarium size, you'll have to have it custom made.

8. Place the aquarium inside the empty TV. Place it inside your console TV and make sure there is a place for everything. Don't install the aquarium yet.

9. Using a drill, make holes for the tube in the rear console cover, if necessary. Also, if possible, make additional holes to improve ventilation and prevent condensation.

10. Make the top cover. The best way is to cut out the entire existing top panel at the seams.

Attach hinges to the base and secure them to the lid so it can be closed and opened. Alternatively, you can throw out the existing top panel altogether and replace it with a flip top made from a new piece of wood, matched to the color of your old console TV.

Place the back of the TV back.

11. Strengthen the bottom of the console if necessary. If you're not sure the bottom can hold gallons of water, you can either replace it with a stronger piece of wood or reinforce it underneath with another piece of wood or a metal lid.

12. Seal all surfaces several times. Use a waterproof polyurethane sealant to protect confined spaces from water damage.

13. Install a voltage stabilizer on the outside of the rear wall of the case, if necessary. If you need to run a cord from the water tank to the power source and it doesn't reach the wall, attach a voltage stabilizer with a long cord directly to the back of the aquarium to bridge the distance.

14. Assemble the aquarium inside the console. Attach the compressor, filter and hoses, then install the aquarium itself.

Install all the above components before filling the aquarium with water and fish, check that everything is working properly. This is absolutely necessary if you want them to live for more than a week or two. If you place the fish directly into the aquarium, then the ammonia formed during the decomposition of their waste products will accumulate in the water faster than beneficial bacteria. So first you need to start the filter and then leave the aquarium alone for at least three days.

15. Done.

Connect the aquarium light through one of the controls on the original TV. To do this you just need to remove it.
Choose an aquarium that is larger than the width of the screen and you will have more water in it, plus you can hide the filter and heater.
This kind of insulation using a console TV for your aquarium will allow you to maintain a constant temperature in it.

Choose a beautiful background for your TV aquarium. You can use underwater scenes (which can be found at most pet stores), or you can choose your own background. (Take measurements and fit your image, then head to your local print shop and print.)
Use the extra space inside as storage for food and cleaning tools.

Warnings

You can take your old TV to a repair shop and have them remove the CRT (Cathode Ray Tube). While the contents of a CRT are usually not dangerous, the air inside the vacuum tube itself can explode if the tube has been cracked or otherwise damaged. (A TV tube until 1960 did not have built-in explosion protection and could be extremely dangerous. If it has a label on it that says something like this: “This tube has built-in explosion protection.”, then you can remove it yourself. If you didn’t see inscription, then it is better to take the TV to a workshop.)

If you use an existing stand, make sure it is strong enough to handle the weight of the water.
Capacitors and other electronics can retain a charge for many years after they were last used. Electrical hazards may still exist, so care should be taken when removing and disposing of electronic components.
Radiation shielding and other components may have very sharp edges.

Make sure you are willing to take on the responsibility of purchasing and maintaining an aquarium. You'll have a lot more trouble than you think!
Make sure you have finished setting up the enclosure before you start placing the aquarium inside.